Many people have the problem of their toilet paper holder breaking. It is a simple enough fix but can be difficult to do on your own if you don’t know what you’re doing. This article will help guide you through the process of fixing your broken toilet paper holder and getting it back up and running as soon as possible!
Fixing a Slightly Loose Toilet Paper Holder
If you have a slightly loose toilet paper holder, you can simply tighten the screws. You can use a Phillips head screwdriver or an adjustable wrench to tighten the screws. Make sure to use caution with any tools and make sure to tighten evenly on both sides of the toilet paper holder.
Choose the correctly sized screwdriver
You will use a Phillips head screwdriver if you have screws that are star-shaped and go in at an angle. You may also use one for flathead screws, but keep in mind that it won’t attach as securely to the screw when turned counterclockwise since the grooves of a flat head aren’t designed with this motion in mind.
If your screws require an adjustable wrench, then they’re most likely square or hexagonal shaped and must be tightened evenly on both sides of the holder so you can avoid any problems during installation.
Tighten it firmly the screw
If you’re using a Phillips head screwdriver, tighten the screws firmly by turning clockwise. If you’re using an adjustable wrench, tighten the screws evenly on both sides of the holder. To avoid damage to your toilet paper holder, make sure not to over or under-tighten them when using a screwdriver.
Make sure that everything is set correctly before putting any tools away so there are no accidents during installation.
Fixing a Very Loose Toilet Paper Holder
If you have a very loose toilet paper holder that won’t stay up, simply follow the steps below.
Locate and remove the screws on the bottom of the decorative arm or escutcheon. Use a Phillips head screwdriver or an adjustable wrench to remove the screws on the bottom of your decorative arm. Keep in mind that you will need two separate tools when tightening so one won’t be enough for this job!
Liftoff the decorative portion of the toilet paper off the bracket
Remove all hardware that secures the decorative portion to the toilet paper roller mechanism. Remember not to lose anything in this process.
Clean any leftover residue or adhesive from where your old toilet paper holder used to be with a small amount of rubbing alcohol on a cotton ball or rag. Allow sufficient time for drying before going on to the next step!
Unscrew the bracket from the wall
Use the Phillips head screwdriver or an adjustable wrench to remove all of the screws holding your bracket in place. You can also drill them out, but make sure that you’re taking precautions with any tools!
Insert a wall anchor
Insert a wall anchor into the hole in the wall where your bracket screws used to be. Make sure that it’s secure with any tools before moving on to the next step!
Replace the wall bracket
Replace the wall bracket and screw it back into place.
Just simply follow this guide above in reverse order of the way that you took things apart.
Replace the decorative portion holder
Replace the decorative portion of the toilet paper holder on the bracket. Attach an appropriate replacement piece according to instructions provided by the manufacturer. Be sure that you know how much weight is attached to each screw when attaching your replacement part or parts.
Tighten the small screws at the base of the arm
Tighten the small screws at the base of the arm before you drive in any screws. This will hold them securely. Try tightening these brackets up again by holding onto decorative portion on toilet paper holder as needed using pliers etc., then reattach it back to the main fixture. Tighten down your replacement hardware too.
Replace toilet paper holder the whole thing
If you have a very loose toilet paper holder that won’t stay up, then it might be time to replace the whole thing. In this case, simply follow these steps below:
Grab your flat head screwdriver and take off all of the screws from where they’re holding down the base in place. You can now pull out each piece until you reach one last screw on either side of the center pole which will hold everything together once removed so make sure not to lose them!
Then just slide off any decorative pieces or covers for a better look at what’s underneath. Next, use a wrench to tighten both sides even when removing old screws since there isn’t much room for error here especially with metal parts being loos by gravity during installation – it’s hard to fix this mistake so be careful!
Grab your Phillips head screwdriver and spray a small amount of WD-40 onto the outside cover before sliding it off. If you’re having trouble getting started, then use pliers to get things going while using your hands for support too just in case. Be sure that each hole is clear from any debris or pieces that might have been left behind during installation by giving everything a quick once over with some compressed air afterward!
Then insert wall anchor into a center pole after cleaning out old holes one more time if needed. Attach decorative portion back on top without tightening screws all the way yet since they need room for adjustment later when attaching bracket underneath instead which should only take about five minutes at most depending on the design of your toilet paper holder.
Now take the bracket you removed from the wall and attach it underneath with screws that are included in most kits before driving them into place instead to avoid any future problems! Once this is done, tighten down all of those small screws first on top by holding onto decorative portion for support using pliers, etc., then reattach back to the main fixture before finishing up.
Just be sure not to over-tighten them when installing new hardware too or else you might strip things which can result in a real headache later on if parts become loose again due to gravity during use!
Conclusion
Most people don’t think about the toilet paper holder until they’re in a situation where it has broken and can’t be used. It’s not something that we usually take time to think about, but when you need one, you need one!
Is the toilet paper holder broken? Now you can fix it easily so you don’t have to wait long before your toilet is fixed again!
And finally – a simple trick: how do you keep toilet paper from unrolling? All it takes is just cut the end of the roll with some scissors and that’s it. You can also use this method on just about any kind of tube-shaped objects, such as wrapping paper or art projects for kids.
